About iLOQ S10 Locking System
iLOQ S10 Deployment Guide
iLOQ S10 Administration Guide
iLOQ S10 Online System and Devices

Home
iLOQ S10 Online System and Devices
Installing and using the S10 Online System and iLOQ devices
S10 Online System
Deploying the S10 Online System Hardware
Quick Guides

Quick Guides

This chapter lists the most common S10 Online System use cases and their configuration instructions.

Connecting a Programming Hot Spot
This section describes how to connect a Programming Hot Spot.
Connecting a Remotely Managed Lock Cylinder
This section describes how to connect a lock cylinder to be remotely managed.
Controlling an Electric Lock by a Calendar
This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be calendar controlled.
Controlling an Electric Lock by a Code-access Group
This section describes how to connect an electric lock, magnet lock or strike plate, and so on, to be code-access group controlled.
Controlling an Electric Lock by a Key Reader or RFID Reader
This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be controlled by a Key Reader or an RFID Reader.
Controlling an Alarm System by a Key Reader or RFID Reader
This section describes how to control an alarm system by a Key Reader or an RFID Reader.
Controlling an Electric Lock by a Combination of a Key and a PIN-code
This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be controlled by a combination of a key and a PIN-code. In this connection, you use a Key Reader and a keypad (RFID reader equipped with a keypad).
Controlling an Electric Lock by a Combination of an RFID Key and a PIN-code
This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be controlled by a combination of an RFID key and a PIN-code. In this connection, you use an RFID reader equipped with a keypad and a key equipped with an RFID chip.
Connecting Monitored Doors
This section describes how to connect monitored doors.

iLOQ S10 Online System and Devices
Installing and using the S10 Online System and iLOQ devices
- S10 Online System
  - Printable Documentation
  - Licenses
  - Net Bridge N100
  - Door Module N102
  - Key Reader / Hot Spot N103
  - RFID Reader N104
  - Bus Addresses and Termination
  - Deploying the S10 Online System Hardware
    - Preparing Net Bridge
      This section describes how to prepare the Net Bridge.
    - Quick Guides
      - Connecting a Programming Hot Spot
        This section describes how to connect a Programming Hot Spot.
      - Connecting a Remotely Managed Lock Cylinder
        This section describes how to connect a lock cylinder to be remotely managed.
      - Controlling an Electric Lock by a Calendar
        This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be calendar controlled.
      - Controlling an Electric Lock by a Code-access Group
        This section describes how to connect an electric lock, magnet lock or strike plate, and so on, to be code-access group controlled.
      - Controlling an Electric Lock by a Key Reader or RFID Reader
        This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be controlled by a Key Reader or an RFID Reader.
      - Controlling an Alarm System by a Key Reader or RFID Reader
        This section describes how to control an alarm system by a Key Reader or an RFID Reader.
      - Controlling an Electric Lock by a Combination of a Key and a PIN-code
        This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be controlled by a combination of a key and a PIN-code. In this connection, you use a Key Reader and a keypad (RFID reader equipped with a keypad).
      - Controlling an Electric Lock by a Combination of an RFID Key and a PIN-code
        This section describes how to connect an electric lock, magnet lock or electric strike plate, and so on, to be controlled by a combination of an RFID key and a PIN-code. In this connection, you use an RFID reader equipped with a keypad and a key equipped with an RFID chip.
      - Connecting Monitored Doors
        This section describes how to connect monitored doors.
    - Finalizing the Bus Device Configuration on Net Bridge
      This section describes how to finalize the bus device configuration on the Net Bridge.
    - Operation Modes
  - Software and Firmware Updates
  - Troubleshooting
- Programmer
- Key Switch R10S.3
- Recycling of Disposed Products

iLOQ Oy, Yrttipellontie 10, FI-90230 Oulu, Finland | +358 40 317 0200 | | All rights reserved - See Terms of use